Free shipping in the United States

How To Install An Above Ground Pool

Above Ground Pool In Orlando
By Pools Above Ground
More from this author

How To Install An Above Ground Pool

How To Install An Above Ground Pool

  A new pool is exciting – especially when it has been installed correctly and is ready to be used. If you have recently purchased an above ground pool and are ready for the installation process, there are some things to be aware of. From choosing the right location to taking measurements and preparing for the unexpected, it's useful to know the right way to install an above ground pool. Regardless of which model you have purchased, there are certain requirements for installation. You should be familiar with the main components of the pool, which will vary slightly depending on the model you have.

But in general, these standard components should away be included:

Gathering the Materials

It is important to have the right tools on hand to make the installation go smoothly. Such tools include a flat shovel or a spade, a hammer or a metal mallet, a sturdy wooden or metal peg, a short wooden stake, a length of durable cord or string, duct tape, and spray paint. If you are installing a larger pool, you should also have a tape measure that can go up to 30 feet or 10 meters.

Choosing the Right Location

This step may seem relatively simple at first, but there is a lot to consider. For example, you need to make sure that the ground is as level as possible and that there are no large stones or rocks in the way. You should also be able to easily access a ground fault protected outdoor electrical outlet. Your pool will be warmer and will stay cleaner if you put it in a place in your yard that gets lots of sunlight. This spot should be clear from trees and large bushes, as leaves can fall in and create quite a mess. Trees and bushes are also home to many different insects, some of which may find their way from the leaves into your pool. Finally, local bylaws and regulations might apply to your area. If so, this may affect how far the pool should be set back from property lines, whether there are any specific fencing requirements, as well as any building permits or other stipulations that may be required. You should check with your local officials before you begin the installation process.

Carefully Mark Where the Pool Should Go

Choosing the right location is important, but so is carefully marking out the spot where you want to put the pool. Once you have made sure that the pool will fit completely and safely into its designated spot, it is time to use some of the tools you have gathered. Mark vital measurements with a can of spray paint. Then, drive the stakes into areas such as corners and the center to ensure that the pool will be lined up evenly. If necessary, use the cord or string to connect the stakes. You can also carefully mark the pool outline with the can of spray paint by going around the intended border.

Prepare the Ground for Installation

Your pool will need an even and level surface. This is where your spade and garden rake will come in handy. Using the perimeter markings as guides, carefully dig away the top layer of grass and sod. You can achieve this by slipping the flat spade underneath the grass, keeping it horizontal as you slowly remove the grass. Cutting the strips into manageable lengths will make this task much easier and will enable you to simply roll up the top layer of grass in a straight line from one side to the other. Use a level or a transit to ensure that the ground is as even as possible.

Lay the Foundation and the Frame

Clear sand is a great choice for your pool’s foundation. This sand should be spread evenly on the ground around the area of grass that you have just removed. Not only does the sand act as a barrier, but it also helps to protect the base of the pool. A two inch even layer of sand is standard for above ground pool installations. However, it is important to check with the specific manufacturer’s instructions for your pool as this number can vary. In addition to the sand, you can add floor padding for extra protection and softness underfoot. A popular choice for above ground pools is Gorilla padding, which is very durable and hard to penetrate. Once the sand is down, you will need to set up the pool’s frame. Stones or blocks that are sunk until even with the ground are popular options. These blocks act as support for the pool.

Constructing the Pool

You can begin putting the pool together after the foundation is ready. As soon as the pool frame and walls are up, it is time to build the cove. A cove is necessary for above ground pools and will keep the liner from slipping under the pool wall. To create the cove, form a 45 degree wedge of sand around the whole circumference of the inner pool wall. Next, take the liner out and inspect it for signs of damage. If it is clear, lay the liner in the sun. The warmth of the sun will make the liner softer and easier to work with. Once the liner is in, stretch it as much as possible without tearing it to ensure that it fits snugly inside the pool. Fill the Pool and Add Your Accessories You can use a garden hose to fill the pool, but a water truck is much faster. As soon as the water is in, you should connect the pump and filter system as well as the heater. This is a good time to install any lights or other accessories that you have, such as a ladder. You will also need to begin adding chemicals to ensure the cleanliness of the water. To do this, simply follow the manufacturer’s instructions so that you use the correct amount.

Above Ground Pool Installation Video by www.poolsaboveground.com

How To Install An Above Ground Pool

December 2, 2013
Comments